Maibec Siding Installation Guide: Costs, Steps, and Advice
A good maibec siding installation guide starts with one truth I learned while inspecting split cedar boards on a coastal home in Maine: real wood moves, and fighting that movement ruins your walls. Factory-stained white cedar looks sharp on day one. Yet improper airflow behind those planks traps condensation and peels paint within three winters.
Homeowners often spend $14 to $22 per square foot installed on genuine Maibec clapboards or shingles. Paying that premium makes sense only when your crew follows strict Canadian Wood Council and manufacturer specs. Let us walk through the exact preparation, fastening rules, and exterior checks that keep genuine wood siding dry for decades.
Maibec Siding Installation Guide — Overview

Maibec mills kiln-dried Eastern white cedar and engineered wood profiles in Quebec, applying two coats of solid or semi-transparent stain inside a climate-controlled plant. Because wood absorbs ambient humidity, bundles must sit flat on your property under a breathable tarp for at least five days before nailing begins. Rushing straight from the delivery truck to the wall causes severe shrinkage gaps once summer heat hits.
Key facts to know first
Acclimation and moisture balance
Boards arrive kiln-dried to roughly 12% moisture content. Store planks at least six inches off damp soil on wooden stickers so air circulates around every bundle. Never wrap the stack tightly in plastic sheeting, because trapped ground vapor warps raw cedar edges overnight.
Required rainscreen drainage gap
A continuous three-eighths-inch air space behind the siding is required by Maibec warranty rules across North America. Furring strips made from preservative-treated pine or high-density polypropylene create this vertical drainage channel. Water gets blown behind lap joints during heavy windstorms, and that open cavity lets liquid drain straight down to your starter flashing.
What most people get wrong
Nailing through overlapping planks
Many general contractors fire framing nails straight through the overlap of two bevel clapboards. That single mistake pins the wood tight against the sheathing and prevents seasonal expansion. When humidity rises in July, the trapped board splits right down the grain line.
Ignoring roofline and flashing transitions
Water shedding from upper eaves destroys freshly hung cedar faster than ground splashback. Before hanging your top courses, inspect adjacent roof edges and review your roof replacement definition if fascia boards show dark rot. Kickout flashing must divert gutter runoff at least two inches away from vertical cedar walls.
Skipping end-grain field sealing
Every crosscut made on the miter saw exposes raw, thirsty wood fibers. Factory stain coats the face and back, yet fresh job-site cuts remain completely unprotected. You must brush matching Maibec touch-up stain onto every trimmed end before fastening the piece onto the wall.
Preparing Your Exterior Wall Assembly
Weather barrier and furring strip layout
Housewrap selection and taping
Wrap your structural OSB or plywood sheathing in a breathable spunbonded polyolefin membrane like Tyvek HomeWrap. Overlap horizontal seams by six inches, and seal every vertical joint with acrylic housewrap tape. Poorly taped seams allow wind-driven rain to soak the wall cavity behind your furring strips.
Vertical strapping spacing
Fasten one-by-three-inch furring strips vertically over every wall stud at 16 inches on center. Use corrosion-resistant screws that penetrate at least one inch into solid framing lumber. Horizontal furring strips block downward drainage and void your 50-year wood substrate warranty immediately.
Essential tools and fasteners for real cedar
Fastener metallurgy standards
Standard electro-galvanized nails rust quickly when exposed to natural tannins inside Eastern white cedar. Only hot-dipped galvanized or Type 304 stainless steel siding nails survive coastal salt air and acidic wood oils. Ring-shank nails provide superior holding power in soft cedar fibers compared to smooth-shank fasteners.
Recommended material checklist
-
Hot-dipped galvanized or stainless steel ring-shank siding nails (minimum 2 inches long)
-
Ventilated starter strip with built-in bug screen to block wasps and mice
-
Matching Maibec touch-up stain and a two-inch natural bristle brush
-
Non-corrosive aluminum or stainless steel Z-flashing for horizontal butt joints
-
High-grade elastomeric polyurethane sealant for window and door trim perimeters
Step-by-Step Siding Layout and Fastening
Starting courses and clearance rules
Ground and roofline clearances
Maintain a strict eight-inch clearance between your bottom cedar course and finished soil or mulch beds. Above asphalt shingles or metal porch roofs, leave a two-inch gap so snow melt never wicks upward into bare wood ends. Homeowners budgeting for simultaneous exterior upgrades often check the full roof replacement meaning before scheduling siding crews, because stripping old shingles first prevents falling debris from denting new factory-stained clapboards.
Leveling the starter course
Snap a continuous chalk line around the entire building perimeter before installing your ventilated starter strip. Check diagonal measurements across corners with a laser level to catch foundation settling early. A crooked first row compounds with every upward course and ruins window header reveals.
Nailing depth and seasonal spacing
Proper nail placement
Drive each nail roughly one inch above the bottom butt edge of the upper board, clearing the top edge of the board underneath by at least a quarter inch. Nail heads must sit flush with the cedar surface without crushing wood fibers. Overdriven nails break the protective factory stain film and create tiny pockets where water pools.
Expansion gaps at trim and butt joints
Leave a one-eighth-inch gap wherever siding ends meet window casings, corner boards, or frieze trim. Butt joints between adjacent planks should touch lightly without being jammed together with a hammer. According to the USDA Forest Products Laboratory Wood Handbook, Eastern white cedar shrinks and swells noticeably across the grain as relative humidity fluctuates between seasons.
Coordinating Exterior Protection and Insurance

Storm damage and exterior envelope planning
Matching roofing and siding timelines
Replacing your roof and wall cladding during the same construction window saves thousands in scaffolding setup fees. Flashing details around dormers and chimneys integrate cleanly when roofers and siding installers coordinate step flashing heights. If storm hail bruised both your shingles and upper gable cedar, verify your policy terms around roof replacement coverage per endorsement meaning so your adjuster accounts for connected wall flashing repairs.
Post-installation maintenance schedule
Wash your cedar walls gently every spring using low-pressure garden hose water and a soft nylon brush. Avoid pressure washers above 500 PSI, because high-velocity water strips soft cedar pulp and voids finish coverage. Inspect south-facing walls every five years for minor chalking before scheduling a single maintenance coat of stain.
Frequently Asked Questions
How much does a maibec siding installation guide project cost per square foot?
Expect to pay between $14 and $22 per square foot for materials and professional labor combined in 2026. Factory-stained Eastern white cedar boards typically run $6 to $10 per square foot alone, while furring strips, stainless fasteners, and skilled carpentry make up the remaining expense.
Can you install Maibec siding directly over OSB sheathing without furring strips?
No, installing Maibec wood siding flat against sheathing violates manufacturer specifications and voids the warranty. You must install vertical furring strips to create a minimum three-eighths-inch ventilated rainscreen cavity behind the boards.
What nails are required for genuine Maibec white cedar siding?
You must use hot-dipped galvanized or Type 304 stainless steel ring-shank nails with full round heads. Standard bright steel or thin electro-galvanized nails react with cedar tannins and leave dark rust streaks down your finished wall within months.
Do you need to seal cut ends during installation?
Yes, every field-cut board end must be brushed with matching Maibec stain prior to nailing. Unsealed end grain absorbs rainwater like a straw and causes paint peeling near window trim and butt joints.
Final Advice Before You Start
Following a reliable maibec siding installation guide protects your investment from hidden moisture rot, split boards, and voided factory warranties. Take time to acclimate your wood bundles, build a true ventilated rainscreen cavity, and seal every crosscut before driving a single stainless nail. Grab a moisture meter, verify your contractor’s flashing plan on paper, and walk your perimeter today to measure exact clearance heights before ordering your first bundle.